Thursday, 11 June 2009

Developments...?

First off, sorry for the lack of any updates of late!

We all went up to Cadwell for the first round on the 16th & 17th May. I went up earlier, to test on the Friday and sort out those carb/ timing niggles.

First off, i noticed that it was decidedly reluctant to get going, worse than the last test at Snetterton...

However, I put the carb needles back to base settings, as per the last laps of Snetterton. Not sure why, but it felt even worse, tho would just about run. Someone had an off on my first lap tho, and they held us all on track just after Mansfield. Told to kill our engines, it was back to the paddock in the Race Support truck. Not for the first time...

So I decided to decrease the size of the needle jet. Running round the paddock it was no better. So the other way, jet up. By that point, I must have been feeling optimistic, and it was our next session, so I tried, but got a few hundred yards before stalling at the slow-running point of the hairpin. Unable to bump it again before it stopped rolling, I sat that one out and waited for the Support van to come and get me again.

I put the carbs back to standard, and then tried to very marginally retard the timing. She still wasn't happy to start, and would barely run at all. Ok then, advance? No better.

By this point, the best part of the day was behind me, and I was no further forward.

To cut a long story short, I fiddled a bit more on Saturday morning, but couldnt even make it out for practice. A bit more time on the carbs and the rollers in the afternoon, but I eventually spat the dummy and went home on saturday night.

On the way home, the heater matrix in the van burst, making for a sauna-like cabin.

So what now then??

Well, I sold the van, and haven't touched the bike. The week after Snetterton got married, and then had a couple of weeks off on honeymoon...

Got back on monday, and I think I may start pondering where to go with this. Perhaps its the cam? Its a stage 4, previously used with a 100mm domed piston. In this motor, its got a 98mm flat-top piston, could this explain why it will only run well above about 5k??

The season's not looking great for me, but I'll keep posting on the development of the bike. For more successful racing-related stories, may I direct the avid reader towards Dave Bennett's excellent www.drbracing23.blogspot.com

Sunday, 10 May 2009

The Empresses New Clothes


Ta Daaa!!

It has been said that the results achieved with doing bodywork stuff are directly proportional to the time and effort put into preparation. Subsequently its looking a bit ropey, but I had no more time, no more aerosols, and it wont matter after a trip through the gravel...

I wish I had more time to make the suface good; more paint (yellow doesn't give great coverage!), and more skill. However, it was a not unpleasant weekend, and as ever, I learned lots. "Every cloud" and all that....

Far from perfect (Andy- its not even "good"!) but at least its now all the one colour. In Team spirit, its akin to Dave's (click that link- his is looking sweet) but I get the feeling that mine will be a poor relation parked up next to his shining jewel!

I only put the bodywork on to make myself feel better on Sunday morning. So the exhaust hangers aren't there, and there bellypan isn't on properly.


From here, I've hung the exhausts, made lower brackets to stop the pipes banging about, sorted that back faster on the bellypan and painted number boards on it.

A bit of soldering to finalise the wiring, add some vinyls (thanks Ash) then off to Cadwell to sort the jetting of Friday. Saturday is the first round of the British Supermono Cup of 2009. I should really have been at this point 12 months ago, but it just didn't happen. And it would still be in multicoloured bits without buckets of help from lots of people. Thank you boys n girls!

Monday, 20 April 2009

She feels fine...

An early morning trek up to Snetterton on Friday, and I was feeling very nervous! The van's been abit rough of late- would it get me there? And the bike's an untested hypothesis- would it work well enough to ride? Or would it clatter to an early death on the back straight? Or would it pitch me off, making life much more complicated than it needs to be?

Ash and his brother Rob were a huge help all day


I needn't have worried, the noise man just laughed when I pitched up for testing. So the whole morning was written off, trying to (ahem!) tune the exhaust with baffles and lots and lots of gaffer tape....

It got quieter with each successive modification, but he still wouldn't let us out. And if I'd have run for more than a few minutes, the tape would surely have melted. However, all wee needed was the "Pass" sticker... And anyway, with so much backpressure it barely ran at all! I managed to buy a couple of new, more restrictive baffles. You can see them plugging up the cans here:









These met with his approval, but then hen the noise man tells us "Oh you were right enough, we whould have been testing at 4000rpm, not 5000"..... So I've missed the mornings test, and I'm thirty quid down.... oh well...










Ash removed the baffles for me, skilled motorcycle engineer that he is!














Anyway, after a bit of fiddling with the timing, she ran, well enough to test.


Dave Bennet took few shots, just so you know I'm not telling fibs! Check out his blog on the Yamatax he's building for Ash.



So she runs, but the carbs need a bit of fettling now. We kind of ran out of time, but managed to get an approximation of base settings for the carbs, the ignition timing and the chassis. And I am in no way to be considered a test rider...!
However, I'm very pleased about the motor. There are many people who have contributed to Friday, and I know its not even a race, and I was slow-slow-slow, but even just a test feels like a victory. So thank you to all who know who they are! Will post soon on the minor fettles before the next test at cadwell, on the 15th May, the day before Round One.

Friday, 10 April 2009

Recalcitrant Single!

Sorry for the lack of info of late! There were a few minor issues to iron out with the motor, involving loose things bouncing around, and part-strips, petrol-soaked shoes and lots of time on the rollers.
A definate reluctance (or rather a refusal) to run had us scratching our noggins.

Ash has rebuilt the carbs, retimed the ignition, checked the cam. And now she runs, and despite re-packing the cans is still pretty loud. So I've got a couple of dB killers coming this week.

We've decided not to bother dynoing it now, but have instead booked a trackday for the 17th April at Snetterton. The back straight should tell us if she's making any power or not... And it will also let us see what the chassis is like initially.

And 4 weeks later, (if the motor holds together) we should be at Cadwell for the 1st round. For a while it looked like she was going to spit the dummy and refuse to run, but Ash cajoled and coaxed her into agreement.

We'll put some pictures up from Snetterton. Promise!

Sunday, 15 February 2009

On Any Sunday

The peace in an otherwise non-descript industrial estate was shattered today with the harsh bark from the cut-down "silencers"; the bike running under its own power for the first time. Finally. About a year later than hoped!

I didn't realise that my hairline was receeding quite so much....



However, Ash described himself as "looking like the man-mountain on that".

We spent the morning fitting crash bungs, here: Also captive nuts to the seat unit, sorting the tank cover and making exhaust brackets. They sit much betrer now. We also fitted a guard to stop small children being sucked into the carbs :

You can see the white plastic guard here, as well as Ash who obviously thinks that he'd be a great bouncer. Looking less thuggish than usual here, he is almost smiling. Despite the hideous exterior, he is a great guy to have onside. I am massively looking forward to the imminent 2009 season.
So, out findings from the initial run: the pipes need brackets underneath, and the silencers re-packing. The battery terminals need to be better secured, and more importantly we need to consider getting some time on a dyno to sort out the ignition timing and the fuelling. There's also an oil weep from the crankshaft where it passes through the CNC ally engine cover, so that will be next. Its getting there, the first race meeting is on the 16th of May. We will be on the grid at Cadwell Park!

Thursday, 22 January 2009

A few hours more...

...and we’re very nearly there!

The weekend was very fruitful, and now with a little bit of faff (oil, fuel, tyres, lockwire, and check fasteners) its testing time.

This is how it was on Saturday morning:



We needed to push a new stem into the yokes, and buy some new bearings. It then became apparent that we had 2 different cups in the steering head- one metric, one imperial! So another favour was pulled in and DBR machined out the lower one to size.


Back to the shed to put it together. On its own 2 wheels, we did those little all-important jobs :

Front and rear brakes, engine and tank breathers, (with a non-return valve in the tank breather). We decided that for the present, we’d use the 5litre tank under the cover, with the under-seat tank and on-going project. Fuel lines, positioning of bars, controls, steering damper and fairing, rearset link rod and rose joints. We fitted the Scitsu tacho, and then decided about placement of the (few) electrical components.

Sunday morning saw a trip to Maplins to buy a small (1.3Ah) battery. You can see it’s a good bit smaller and lighter than the 3Ah one I had planned on. I will just have to keep an eye on charge etc. I think a spare would be a good idea for a race weekend!



We put the Silent Hektic ignition unit under the battery at the front fairing stay, and the coil beside this.

It was decided that it was (reasonably) out of harm’s way, and would be kept quite cool. The problem with carrying the oil in the frame is that it quite quickly gets rather warm…!

Ash stuck on a toe-guard

while I made the tea!

The blue seat unit weighs about 2 elephants, so we decided to recycle Ash’s old red one. We’ll need some captive nuts for this to enable speedy strips and mounting, but that’s not a problem. it’s a lot lighter and looks a bit more modern too- I’m guessing this seat unit is a later development of the Tigcraft chassis

And that was the state of play on Sunday night
Looking good eh?? I can’t wait to just do the few little things, then hopefully, around the end of Feb, we can get back on track. Cadwell’s the first round on the 16th of May!

Sunday, 11 January 2009

Happy New Fuel Tank








I’ve been thinking about fuel tanks of late. The original tank, holding 5 litres sits under this cover, but may be just a little too small.






A phone call to Dave Pearce at the Tigcraft Technology Centre was very fruitful. He let me have not one but 2 tanks, for an absolute steal. Thanks for that Dave, very much appreciated.



Option one is 7 litre plastic job, which could live under the existing (or my spare) seat unit.











This was originally on a Derbi GP50, but could potentially solve our problem.



Secondly, he also gave me (for a song), a manx tank, which looks like it holds about 18 litres! As he said, we’d probably only have to fill it up at the start of the season…”. Dave also observed that it did appear to have fallen out of the ugly tree, but maby it could be judiciously modified by someone who knows what they’re doing. there’s certainly enough sheet ally to work with there!



I think it was made for flying Scotsman Denis Gallagher for the '99 Singles TT, and then passed thru the hands of Andrew McCombe before coming back to Dave.

Next to it is the carbon fibre cover.

The bike is still out at Ash’s, I’ll report more after we get the front end together next weekend. And there may be another seat option too...
Finally, provisional dates have been published for the upcoming season:
Cadwell May 16-17
Snetterton June 19-20 BSB Combined UK & Euro-round
Brands GP July 25-26 (Possible UK/Euro-round)
Snetterton September 5-6
Brands Indi September 26-27
Plus probably one more weekend in either April or August to give a championship of 6 weekends. I'm getting excited!

Thursday, 27 November 2008

Carry on Racing!


Now then!


Here’s a little insight into what has been going on over the last few weeks. The bike’s been at Ash’s place out in Manningtree, home of the beautiful Robert Adam-designed Mistley Towers...

However, I digress, for I did not go out there to admire the fine architecture.




Oooooh No! Missus!




I went out there (on the coldest day of the year) to help young Mr. Norrington put up his new shed. It was a fabulous erection; although I do owe him heavily for his help with the 640 Tigcraft.

It became apparent that our steering stem (previously using a 12mm bolt...!) wasn’t up to snuff, so we knocked out a stem from Ash’s old (crumpled) frame, and with a bit of engineering work, this can be reused. We had to play about with the steering head cups a bit, and I’ll need some bearings but these are not major problems.

Despite the lever being attached to the cheapest nastiest clip-ons in existence, the front brake seems to be working, now it’s been bled.

We’ve also re-sited the pipes, and now they appear to sit a bit better.

The heavy and rather large...


...one-piece seat unit may be ditched in favour of an ally subframe and lightweight race seat unit..., ...but as it is, it works, so maybe we will start the season with the original.

However, there is more important news than mere motorcycles! In an effort to play to combined strengths, we have decided to consolidate our (your?!) own Team Thumper with Ash’s Moto450Supermono. So now that we have become a happy threesome (can a threesome be anything else?!), and, given the grave world financial situation its 2 for 1.

2 bikes, 2 vans (neither warrant a photo), 2 riders, and Boyd Brooks- the 2Bs!



Ash's CRF450-derived racer is full of the trick bling, nice wheels, and looks the business. A welcome addition to the usual rag-tag which has so far defined Team Thumper!














Derby’s finest has been sorting out a remanufacured front fairing stay/tacho mount. Soon this will also be down in Manningtree and we can get a bit more progress once she is back on her own 2 wheels.


The only other thing we need is a name...

TeamThumperMoto?

TeamThumperSMR (as in SingleMindedRacing)?

Answers on a postcard plase to the usual address. Any suggestions welcome...

Thursday, 30 October 2008

Bling Bling!

Well, here’s the rather lovely R6 radial caliper mount. I’ve not seen it in the flesh, but Ash sent this from his mobile. Technology eh??

The bike’s at his place now, thank you matey. And to Mark at DBR for the beautiful looking chunk of ally on my forks! And if you need any more convincing of his prowess, I hadn’t realised, but it turns out that he also made the blanking plate for where the water pump used to be. He recognised it when we turned up with the bike. Small world, eh? I wonder if the nice swirl which has finished it off will make it any faster….?


And given the press fanfare of the recently re-anglified Norton Motorcycle Company, a name forever associated with single cylinder race bikes, we can hardly not wish them the very best of luck… Ok, so we’ve been here before, and the great name has had a rough time over the last decade or so (Norton Nemesis, anyone?) but if they can turn up beautifully engineered bits of kit as quickly as DBR then they’re half way there. Will the Crighton and Garner partnership result in new Nortons on the road in the next few years? Lets hope so. Now, could a single-rotor rotary motor ever be considered eligible for Supermono…?!

Saturday, 25 October 2008

What News, Sire?

Well, this week has been relatively fruitful. Long, dark, cold nights are no better spent in the closed season than in a short, dark, cold garage.

The sloppy swingarm has been cured by using the correct spacers, and the bike now sports a single 320mm disk upfront. After a long day at work Wednesday, I got home, loaded up the van and completed a 200 mile round trip to deepest darkest Essex. After a couple of hours driving I met Ash Norrington at a layby off the A120, with him as ever grinning like a loon! I think he had been dogging, actually…

He took us (me and the bike) out to see Mark, who runs D.B. Racing in Thorpe-Le-Soken, specialising in CNC-machined bits and pieces for racers and roadbikes alike. His workshop was more like a lab (fastidiously clean, spacious, well lit, no sh*t lying around- clearly not MY lab!!), and I was impressed by both his facilities and his attitude. Nothing was too much of a problem, “Yes, we can do that”. Great!

Ash is still concerned about our rear shock keeping the back end rather low, but he may be able to help us out (again!) with something.

Will post some piccies of the bling-bling brakes when I pick up the bike.

***STOP PRESS!*** I just got a call from Ash. Its done! Will try to pick up asap and post a coupla photos.

Monday, 13 October 2008

A bit of video...

This is a bit old, but shows the first time running.

And how stupid we can be, trying to bump it in neutral!

I couldn't figure out how to flip it, so one of the videos is on its side. Just tilt your minitor to enjoy the buffoonery! :)




Thursday, 9 October 2008

Nic says...

“Update yer blog!” So in answer…

The bike runs, its just about complete, electrics such as they are, are ready to be laid on, the bodywork fits, cables, levers, bars, steering damper, all good. Brakes… After our screwing around with the (knackered) KR1S callipers, and twin FZR400 300mm disks, Ash came up with a great solution, which suits the Scotsman’s wallet.

He has been an absolute diamond by sorting out Team-Thumper with an R6 calliper and RS125 master cylinder. And Supermono stalwart Nick Oliver also threw a 520 chain our way; top bloke, thanks Nick.

We caught up at the final round of the British Supermono Championship of 2008. Although we weren’t in a position to compete, we did witness to some great racing, and met up with old friends. Ash’s CRF450-based racer is a thing of beauty, and I’m looking forward to a bit of a scrap next season.

So now we need to get a calliper bracket machined up (probably CNC, from DB Racing). It’s a radial calliper, onto our distinctly 1990s fork legs. We also now have 320mm disks. One for our wets, one for the slicks, as we are now going to run a single large disk, saving a decent amount of (unsprung) weight, as opposed to twin 300mm disks.

The whole thing has been dragging on a bit, not helped by the van needing an MOT… So there’s been a month of hand-wringing, and head scratching, before finally forking out. Cos a race team without a van is like…. a chav without Burberry. Or Sovvy rings. Or a Staffie. Or something like that.

I thought that the swingarm needed some spacers turning up, but on tidying the garage last night, I found a suspiciously homeless looking ally spacer which I’m willing to bet takes up the play between frame and swingarm.

No photos on this post, cos nothings changed! But we won’t leave it so long next time- promise! Testing soon?? There’s really not too much in our way now….

Monday, 11 August 2008

She Runs!!

Hurrah!!

We got her on the rollers last weekend, and ran like a good un!

Even with the approximate timing and jetting, I'd say the motor is now ready to test. She sounds nice tho, even if I say so myself.

The chassis will definately require a little tweaking to give me confidence to test it on a circuit tho! I think Ash is gonna help me out on the braking side of things... Watch this space!

I think there is a little bit of video floating about. As sson as I can get it off my mate's phone, I'll post it up here.

Cheers

Andy

Tuesday, 15 July 2008

Ash-en Faced!


Given the unholy speed with which fellow supermonoist Ash is throwing together his very tasty looking CRF 450-based project, (click it; he puts us to shame!) and the excruciating pace of ours, we had better get the finger out.

Its not that we’ve not been working, but there were some minor yet fundamental details which needed sorting:

So:

oil lines- check! Thanks Ben at Pirtek...
exhaust springs- check!
clutch lever assembly- check!
front brake line- check!
stripped thread on the brake caliper –sadly, also check….
the all-important kill switch –check!
ignition timing- check, check and check again!

You can see the trigger for the latter on the end of the crankshaft. Its a Silent Hektik unit, and allowed me to ditch the hefty alternator rotor/flywheel unit.


It also became evident that the cam was a tooth out, so I’ve had the engine out and back in as well. One tooth- “a minor yet fundamental detail”…

So these photos now show rather less of a mock up and more of a near-final machine.

Boyd will soon be on the case with a battery box and a few little brackets (ahem! once I send him some details on sizes etc- sorry mate!). However, as previously, these can be secured with cable ties. We just need to get her on the rollers. Because now I think with some oil in the frame, some fuel in the tank, and a car on the rollers, she may be in a position where she'll bang and pop. I do have the feeling that the 145 jets in the Keihin CR33s will be too big (these were feeding a 690 motor), and that the ignition timing is very approximate. But we need a starting point and now its tantalisingly close.

However neither of us can meet until 3 weekends from now. Life has seemed to get in the way of Team Thumper. This is piss! More on that later. And priming the oil system would seem like a very good idea. This will require running (plug out) on the rollers until we are sure there are no air locks and that its all getting where it should. Even when the motor turns by way of 4-stroke internal combustion principles we then have the chassis to address. Of course, a test day at Mallory may show that she handles absolutely beautifully, runs in without any drama and then gives herself a lick of paint whilst driving us back from the pub. Although I feel even most optimistic reader will know that this is not an entirely likely scenario.

It has been noted that it has taken us an unfeasibly long time to get ourselves into a semblance of shape. And we have had a lot of help from lots of people, to whom we are indebted. Thus the executive decision has been taken that we will have to compete next season. However, the author hasn’t quite broken it to one of the (generally) silent partners of Team Thumper. I am almost certain that she does not read this….

Wednesday, 25 June 2008

Poco a Poco...

So now we have a rear master cylinder, and some exhaust brackets. Every day she grows a little more!





And I know the exhausts look a bit daft from the back, but at this rate there wont be anyone behind me to see them...







Am not sure whether to take a front disk off, or add a second caliper. Either way, not a massive job, I am sure testing will sort that one out!

And once I get a few little fiddly jobs out of the way I'll have to get wiring in the Silent Hektik ignition system. Oh...! And that reminds me, we'll need to make a battery tray too!

Saturday, 21 June 2008

Slow but Steady...


...kind of sums up Team Thumper I suppose!


A bit of a progress report on the current state of play:


Today I fibreglassed the necessary fixings and exhaust brackets onto the tail unit; you can see the standard of workmanship here...!


I also got a (barely) functional rearset linkage on the go, to at least allow me to knock it into gear when the time comes to try to run it.






On top of that, we now have a chain (to facilitate the same), and I've cleaned up the front fairing bracket to allow a bit of welding to be done.



But its almost a bike now: the tail unit is ready to go, and the brackets for the little ally tank have been bodged out of some flattened tube. I have the distinct feeling that when it comes to actually running (reliably), then they'll have to be re-made, but they'll do for just now. She is beautifully narrow across the waist tho; we have faith in the belief that when she runs, she should be a good 'un. Getting to that point has just been more problematic (for oafs like us) than we'd ever though would be the case...

Slightly more problematic may be mounting the rear master cylinder as space would appear to be rather tight. Nice rearsets tho, eh??
Note the lower bolt in this pic (there are 4 in total) which support the seat unit and rider's weight; impressive given the lack of subframe.

Oil lines should be on within a week. Ditto the front brake line. Then after a bit of wiring, and finding a clutch lever and handlebar bracket, I would hope that we can start to think about fuelling up and putting some oil in... then Boyd can break a sweat pushing me and a dead bike up and down the street!!

Tuesday, 10 June 2008

Progress!

3 sets of valve stem seals, 2 camshafts, lots of thinking and stupid questions, long hours filing collets and a complete lack of any engineering prowess.

The motor is now in the frame and all the major bits are hanging on it. It even rolls... Oil lines have been problematic, tho Ben at Pirtek at Kings X has been trying hard to sort out the niggles.

I have a chain on its way, an immediate problem is the shift linkage. I have RH thread rose joints (M6 thread and 6mm pivot hole), and some M6 bar which will do for a link rod just now. However, all of the gear shaft clamps I have have old knackered rose joints (with LH threads) pressed in... And they wont press out. I need a clamp to bite onto the gear shift splines, with no rose joint on it...

Back the the Electronic Bay. Do such items exist? I'm about to find out...

Piccies soon!

a

Tuesday, 6 May 2008

Terrible Headaches!

Here’s a bit of an update after a rather prolonged silence. Rest assured that while we’ve been a little lax in updating the blog since Snetterton, things are progressing. As usual there’s been more thinking than actually doing!!

Oil lines should be on their way from the friendly and helpful guys at Pirtek at Kings Cross (cam feed and main tank-motor and motor-tank oil lines). They’re also fixing me up with a front brake line. However, inside the motor, I’m still fretting about the valve gear, and we are acutely aware that time is marching on. Having received the oversize shims from Rog Key, I re-checked the spring installed height; they’re all now spot-on. However, I then wanted to just make sure that the collets weren’t going to do anything comical with the valve stem seals at full lift.


The subject of much domestic strife….!

The valve guides have already been shortened for use with the Stage 4 Megacycle cam, and the motor apparently ran very well. It may have broken the bottom end, but the top was fine!

However, the pattern valve stem seals I received were not a particularly good fit. At full valve lift (measured rather inaccurately at 12.1mm for the inlets and 11.4mm exhaust) there was indeed contact. I only tried it on one inlet valve, but turning the cam by hand was enough to feel contact. I tried to get the seals to sit a bit further down the guide but to no avail. They may have been cheap, but I can hear my old man warning me “Buy cheap, Pay dear”. Paying dear would almost certainly result from a dropped valve. I resent the time and hassle more than anything: rockerbox on, rockebox off, cam in, cam out, setting/checking the tappets every time. Measure, turn, check lift, blah blah blah! So now you see why the blog’s not been updated?? This part is just too boring, and time consuming!

A second old adage of my father’s is “Buy cheap, Buy twice”. Another accurate observation from the old felly. I duly received my new Yamaha valve stem seals Fowlers on next day delivery, having placed an order at 4-30 the previous afternoon. Top service. I was pleased to find that as a result of their better fit, there was now clearance. Not as much as I’d like admittedly, but there is clearance. And the new collets are no bigger than the old ones, so I’ll probably go with it as is. Unless of course I could remove just the slightest amount of metal from the bottom of the collets…? Hmmmm, probably not.

As a little aside, measuring lift accurately is difficult as I am not, by any stretch of the imagination, an engineer. Working with a only vernier (“very-near”) caliper is difficult in the confined space of the head. And the curves of the valves and inside the combustion chamber make it hard from that side.

So having previously made a note of the lift, I then built up the collets and retainer without the springs. You can see this here, and underneath the R/D bottom cup is Rog’s shim.


So how to measure? I ended up bodging on a bit of plasticine, removing it and measuring the distance between the top of the seal and the bottom of the collets.



Obviously not the most accurate, but just about the only way I could think of doing it. And I think it will do, in the absence of any other expertise…! Or am I just showing myself to be a fool, who can’t build an engine? Well, you can all say “I told you so” when it drops a valve!

Right. Lets get this head on!